Pfeiffer Vacuum HiScroll 6 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, Manual Gas Ballast, No Pressure Sensor, 100-240 VAC, 3.6 cfm, KF-25 Inlet & Outlet, 1-Phase. Pfeiffer Part Number: PD S10 000 B. This Pfeiffer HiScroll 6 dry scroll roughing/backing pump Standard Version Includes ATEX certification and Manual Gas Ballast, No Pressure Sensor. It can reach a pumping speed of 3.6 cfm (6.1 m3/hr), and an ultimate vacuum of 1.5 x 10-2 Torr (2 x 10-2 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 6 pump draws 4A@120VAC (2A@240 VAC) and is extremely quiet at 48 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 6 dry scroll pump has part number PD S10 000 B. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer Vacuum HiScroll 6 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, No Gas Ballast, No Pressure Sensor, 100-240 VAC, 3.6 cfm, KF-25 Inlet & Outlet, 1-Phase. Pfeiffer Part Number: PD S10 001 B. This Pfeiffer HiScroll 6 dry scroll roughing/backing pump Standard version includes ATEX certification, without Gas Ballast or Pressure Sensor. It can reach a pumping speed of 3.6 cfm (6.1 m3/hr), and an ultimate vacuum of 1.5 x 10-2 Torr (2 x 10-2 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 6 pump draws 4A@120VAC (2A@240 VAC) and is extremely quiet at 48 dB(A). This HiScroll pump has internal motor protection. ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer Vacuum HiScroll 12 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, and Manual Gas Ballast, No Pressure Sensor, 100-240 VAC, 7.1 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S20 000. This Pfeiffer HiScroll 12 dry scroll roughing/backing pump Standard Version features ATEX certification and manual gas ballast, without a Pressure Sensor. It can reach a pumping speed of 7.1 cfm (12.1 m3/hr), and an ultimate vacuum of 6.75 x 10-3 Torr (9 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 12 pump draws 8A@120VAC (4A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 12 dry scroll pump has part number PD S20 000. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer Vacuum HiScroll 12 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, Manual Gas Ballast, and Integrated Pressure Sensor, 100-240 VAC, 7.1 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S20 010 B. This Pfeiffer HiScroll 12 dry scroll roughing/backing pump Standard Version features ATEX certification and manual gas ballast, with integrated Pressure Sensor. It can reach a pumping speed of 7.1 cfm (12.1 m3/hr), and an ultimate vacuum of 6.75 x 10-3 Torr (9 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 12 pump draws 8A@120VAC (4A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. This Hiscroll 12 pump with the pressure sensor option provides pressure regulation by varying the speed of the pump so that a target pressure is achieved. Pressure regulation operation is effective in the range between final pressure and 22.5 Torr (30 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 12 dry scroll pump has part number PD S20 010 B. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer Vacuum HiScroll 18 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, and Manual Gas Ballast, without Pressure Sensor, 100-240 VAC, 10.7 cfm, KF-25 Inlet & Outlet. Pfeiffer Part Number: PD S30 000 B. This Pfeiffer HiScroll 18 dry scroll roughing/backing pump Standard Version Includes ATEX certification and a Manual Gas Ballast, without a Pressure Sensor. It can reach a pumping speed of 10.7 cfm (18.1 m3/hr), and an ultimate vacuum of 5.25 x 10-3 Torr (7 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 18 pump draws 10A@120VAC (6A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 18 dry scroll pump has part number PD S30 000. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer Vacuum HiScroll 18 Oil-Free Dry Scroll Vacuum Pump Standard Version Includes ATEX, Manual Gas Ballast, and Integrated Pressure Sensor, 100-240 VAC, 10.7 cfm, KF-25 Inlet & Outlet, 1-Phase. Pfeiffer Part Number: PD S30 010 B. This Pfeiffer HiScroll 18 dry scroll roughing/backing pump Standard version Includes ATEX, Manual Gas Ballast, and Integrated Pressure Sensor and can reach pumping speed of 10.7 cfm (18.1 m3/hr), and an ultimate vacuum of 5.25 x 10-3 Torr (7 x 10-3 mbar). It has KF-25 (NW25) inlet and outlet ports. Input of 100-240 VAC, 50/60 Hz, single phase power is required and and the pump has a standard C14 input power connector. The HiScroll 18 pump draws 10A@120VAC (6A@240 VAC) and is extremely quiet at 47 dB(A). This HiScroll pump has internal motor protection and an integrated two-stage gas ballast which allows for pumping of condensable vapours including water, solvents, dilute acids and bases. Maximum dry air or inert gas ballast pressure is 21.7 psi (1500 hPa). ATX HiScroll pumps are dry, oil-free scroll vacuum pumps designed for use in environments with explosive atmospheres, which is indicated by the "ATX" (ATEX) certification. This Hiscroll 18 pump with the pressure sensor option provides pressure regulation by varying the speed of the pump so that a target pressure is achieved. Pressure regulation operation is effective in the range between final pressure and 22.5 Torr (30 hPa). The pump has an onboard inverter controller which allows the pump to be controlled either manually with easy-to-use push buttons, or remotely via RS485 when connected to a Pfeiffer DCU or OmniControl controller, or a user supplied software interface. The pump controller has a standby mode and when active reduces the speed of the pump to 50% of full speed to save wear and tear on tip seals and to increase bearing service life. This Pfeiffer HiScroll 18 dry scroll pump has part number PD S30 010 B. About the Pfeiffer HiScroll Series of Dry Scroll Vacuum Pumps: The Pfeiffer HiScroll dry scroll vacuum pump series consists of three dry and hermetically sealed scroll pumps with a nominal pumping speed of 6 - 20 m3/ h. The pumps are especially characterized by their high performance when evacuating against atmosphere due to their unique features. Their powerful IPM synchronous motors achieve an efficiency that is up to 15% higher than that of conventional drives. The pumps are also characterized by their very compact design and extremely quiet and low-vibration operation. Therefore, they are ideal for use in quiet working environments, for example on mass spectrometers, research & development institutes or leak detection systems. The Pfeiffer HiScroll dry scroll vacuum pumps can be easily connected to other Pfeiffer Vacuum products (such as turbopumps or display and control units) as well as to a higher-level external controller, via RS-485 or ProfiNet. The interface enables RPM regulation, situation-specific control of the fan and monitoring of the pump performance. This helps to minimize wear and noise emissions, and ensures longer maintenance intervals. The integrated two-stage gas ballast and safety valve ensure process-specific and safe operation. The proven quality of Pfeiffer Vacuum components guarantees pump longevity. Easy maintenance enables short service times and the efficient motor helps to reduce electricity costs. We carry all the replacement parts and rebuild kits to maintain and keep your Pfeiffer HiScroll vacuum pump in peak operating condition. Please see the operating instruction manual in the downloads.

Pfeiffer OEM Tip Seal Maintenance Kit for HiScroll 6 Scroll Vacuum Pumps. Pfeiffer P/N: PD E10 000-T This is a Pfeiffer OEM Tip Seal Maintenace Kit for Pfeiffer HiScroll 6 Scroll Vacuum Pumps. These are user friendly replaceable.

Pfeiffer OEM Tip Seal Maintenance Kit for HiScroll 12 or HiScroll 18 Scroll Vacuum Pumps. Pfeiffer P/N: PD E20 000-T This is a Pfeiffer OEM Tip Seal Maintenace Kit for Pfeiffer HiScroll 12 or HiScroll 18 Scroll Vacuum Pumps. These are user friendly replaceable.

Pfeiffer Screw Cap for Gas Ballast on 6-12-18 HiScroll Vacuum Pumps. Pfeiffer P/N: PD 100 067 This is a Pfeiffer Screw Cap for the Gas Ballast on 6-12-18 HiScroll Pfeiffer Vacuum Pumps.

Pfeiffer HiScroll 6 -12-18 Push-in fitting coupling G 1/8 including seal for hose connection (8/6 mm). Pfeiffer P/N: P 4131 029 G NEW Pfeiffer HiScroll 6 -12-18 Push-in fitting G 1/8 including seal for hose connection (8/6 mm) to be connected to an external supply with nitrogen (N2) or another dry, inert gas to this coupling.

Pfeiffer Inlet Dust Separator for HiScroll 6-12-18 Scroll Pumps, Polyester Filter, KF25. Pfeiffer P/N: PK Z60 507NEW Pfeiffer Inlet Dust Separator for HiScroll 6-12-18 Scroll Pumps, Polyester Filter, SAS 25 S, KF25. Prevents dust particles entering into the inlet of the Scroll Pump. Allows longer service life of mechanical parts.

Pfeiffer RPT 010 Digital Piezo Pirani Sensor for HiScroll 6-12-18 Scroll Pumps. Pfeiffer P/N: PE 100 183 -XThe HiScroll vacuum pump is equipped with a pressure sensor in the pumping system, either directly or by way of installation (optional accessory). This digital Piezo/Pirani sensor RPT 010 measures the intake pressure of the vacuum pump. Certain functions described for the vacuum pump are only available with a pressure sensor installed. This Sensor Measures coarse vaccum independent of gas type. Pressure Range 1 X 10-4 - 1200 hPa. NOTE: To connect the RPT 010 Piezo Pirani Sensor, See Operating Instructions .pdf to the left at downloads.