Agilent Varian cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge, 3 foot length. This is a Varian Agilent signal cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge. This is 3 foot cable length. This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge, 10 foot length. This is a Varian Agilent signal cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge. This is 10 foot cable length. This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge, 25 foot length. This is a Varian Agilent signal cable for CDG-500 Capacitance Manometer Vacuum Pressure Gauge. This is 25 foot cable length. This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian PCG-752 KF16 Pirani Capacitance Diaphragm Gauge With Single Nickel Filament Pressure Range Atm to 3.8 X 10-5 Torr, KF16 This Agilent Varian PCG-752 Pressure Gauge is a Pirani Capacitance Diaphragm with a single nickle filament design. The gauge can measure pressure from 3.8 X 10-5 Torr to atmosphere. This PCG gauge is a combination gauge consisting of a Pirani sensor and a diaphragm capacitive sensor. Both sensors are constantly active. At low pressures, only the signal of the Pirani sensor is used for pressure measurement; at high pressures, only the signal of the diaphragm capacitive sensor is used. To determine the output signal in the intermediate range, both signals are used proportionally to the pressure.This is the PCG-752 pressure gauge only and has a KF-16 vacuum flange fitting. No Set Points, No Display, No Profibus. User replaceable nickle sensor, signal cables and pressure controllers sold separately on this website. A complete Operating Instruction Manual and Spec Sheet is available for download in pdf format below under AVAILABLE DOWNLOADS. Compatible with Agilent Varian Pressure Gauge Controllers: XGS-600 Multi-gauge Controller Active Gauge Controllers AGC-100, AGD-100

Agilent Varian PCG-750 Pirani Capacitance Diaphragm Gauge Replacement Sensor with Tungsten Filament.Pressure Range Atm to 3.8 X 10-5 Torr, KF16.This Agilent Varian Tungsten Replacement Sensor is for the PCG-750 Pirani CDG Gauge with KF16 Flange. This filament sensor is replaceable by the user. The gauge can measure pressure from 3.8 X 10-5 Torr to atmosphere. This PCG gauge is a combination gauge consisting of a Pirani sensor and a diaphragm capacitive sensor. Both sensors are constantly active. At low pressures, only the signal of the Pirani sensor is used for pressure measurement; at high pressures, only the signal of the diaphragm capacitive sensor is used. To determine the output signal in the intermediate range, both signals are used proportionally to the pressure. This is the replaceable tungsten sensor with the KF16 flange. This replacement sensor is for the PCG-750 Pirani CDG combination gauges only. Signal cables and pressure controllers sold separately on this website. A complete Operating Instruction Manual and Spec Sheet is available for download in .pdf format below under AVAILABLE DOWNLOADS. Compatible with PCG-750 Pirani CDG gauges (with tungsten filament) Part Numbers: PCG750KF16 PCG750KF16SD1 PCG750KF16SD2 PCG750KF16SD3 PCG750KF16SP

Agilent Varian PCG-752 Pirani Capacitance Diaphragm Gauge Replacement Sensor with Nickle Filament.Pressure Range Atm to 3.8 X 10-5 Torr, KF16.This Agilent Varian Nickle Replacement Sensor is for the PCG-752 Pirani CDG Gauge with KF16 Flange. This filament sensor is replaceable by the user. The gauge can measure pressure from 3.8 X 10-5 Torr to atmosphere. This PCG gauge is a combination gauge consisting of a Pirani sensor and a diaphragm capacitive sensor. Both sensors are constantly active. At low pressures, only the signal of the Pirani sensor is used for pressure measurement; at high pressures, only the signal of the diaphragm capacitive sensor is used. To determine the output signal in the intermediate range, both signals are used proportionally to the pressure. This is the replaceable Nickle sensor with the KF16 flange. This replacement sensor is for the PCG-752 Pirani CDG combination gauges only. Signal cables and pressure controllers sold separately on this website. A complete Operating Instruction Manual and Spec Sheet is available for download in pdf format below under AVAILABLE DOWNLOADS. Compatible with PCG-752 Pirani CDG gauges (with Nickle filament) Part Numbers: PCG752KF16 PCG752KF16SD1 PCG752KF16SD2 PCG752KF16SD3 PCG752KF16SP

Agilent Varian Eyesys, Replacement Transducer for CT 100 Active Rough Vacuum Gauge, KF16.Agilent Varian Eyesys Replacement Transducer for the CT100 Active Rough Vacuum Gauge, KF16 fitting. Signal cables and pressure controllers sold separately on this website.

Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1.33 in. CF Conflat Flange, 304L Stainless SteelPressure Range: 1 × 10-3 torr to Atmosphere, Maximum bakeout temperature: 80 °CThis is a Varian Agilent ConvecTorr Convection-Type Tube Sensor, 1.33 in. CF Conflat Flange, 304L Stainless Steel, Pressure Range: 1 × 10-3 Torr to Atmosphere, Maximum bakeout temperature: 80 °C. The Varian, Agilent ConvecTorr Gauge Tube is ideally suited for vacuum-system applications where accurate pressure monitoring is required and rapid, repetitive pumpdowns from atmosphere are the norm. The ConvecTorr Gauge Tube, unlike common convection-type gauge tubes, is not affected by system vibration. Its dependable design offers continuous and repeatable pressure indications at temperatures from 0 °C to 50 °C. The tube has been optimized for convection cooling, resulting in superior readings at higher pressures. The electrical connector is a locking bayonet type. The ConvecTorr gauge is offered with a variety of flange connectors and is easily interfaced with Varian Agilent XGS-600 gauge controller for integration in a complex vacuum system, or for use as a stand-alone pressure measurement tool.

Cable for Agilent XGS-600 SenTorr Gauge Controller to ConvecTorr Sensor. 7.6 m, 25 ft. This cable connects Agilent ConvecTorr sensors to an Agilent XGS-600 controller, Multi-Gauge controller, or SenTorr Gauge. It is 10 ft. long (3 m). This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Cable for Agilent XGS-600 SenTorr Gauge Controller to ConvecTorr Sensor. 7.6 m, 25 ft. This cable connects Agilent ConvecTorr sensors to an Agilent XGS-600 controller, Multi-Gauge controller, or SenTorr Gauge. It is 25 ft. long (7.6m). This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian 50 Foot Cable connects XGS-600XGS SenTorr Gauge Controller to ConvecTorr Sensor. Signal cable, 50 foot length. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Varian ConvecTorr Sensors. Cable 50 foot cable length.Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian IMG-100 Inverted Magnetron High-Vacuum Gauge, NW40, KF40 FlangePressure Range: 1 × 10-3 Torr to 5 × 10-9 Torr.This is a Agilent Varian IMG-100 Inverted Magnetron High-Vacuum Gauge, NW40, KF40 Flange, Pressure Range: 1 × 10-3 Torr to 5 × 10-9 Torr. Maximum Bakeout Temperature: 150 °C (with cable disconnected), Materials Exposed to Vacuum: Stainless Steel, Nickel, Nickel Alloy 52, Glass. The IMG-100 is a rugged and accurate high vacuum gauge featuring a wide measurement range, fast starting time, good accuracy and superior repeatability in challenging environments. The IMG-100 is ideal for use in industrial applications such as metal deposition, glass coaters, vacuum furnaces, degassing ovens, and electron-beam welders. The simple design requires no heated filament, so the IMG-100 has an excellent lifetime, is easily serviced, and is tolerant of sudden or frequent exposure to atmosphere.Further, there is less risk of heat from the gauge interfering with a critical experiment or process. The compact size allows flexible installation in any orientation, while the locking SHV high-voltage connector ensures safety and positive electrical contact. A precisely designed magnetic field constrains ionized gas molecules for accurate pressure measurement, so emission of stray electrons and photons is minimized. The IMG-100 is easily interfaced with Varian’s XGS-600 gauge controller for integration into a variety of vacuum systems, or for use as a stand-alone pressure measurement tool. This is the Agilent Varian IMG-100, NW40, KF40 Flange, gauge only, signal cable and controller sold separately on this website. The complete operating instruction manual and other pertinent data can be download in pdf format below. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller

Agilent Varian 563 Glass Ion Gauge Tube, Tungsten filament, 1 inch NONEX Port, Vacuum Pressure Gauge.These Ion Gauge Tubes have a 1 inch port vacuum connection and an operating range from 1x10-3 to 2x10-10 Torr. These ion gauge tubes are compatible with most modern hot cathode ion gauge tubes. They have a sensitivity of Torr-1 and standard operating voltages (collector 0 VDC, Grid +180 VDC, filament +30 VDC with 4 VAC filament voltage). In high and ultra-high vacuum ranges, a platinum shield prevents external electrical fields from affecting the low ion current. In higher pressure ranges where the number of ions produced is much greater, the platinum conductive coating drains off the static charge which can build up on the inside of the glass tube. Thus, the 563 tube gives superior performance throughout the entire range of the tube. Our replacement ion gauge tubes work with most hot cathode ion gauge controllers made by Granville Phillips, MKS Instruments, Perkin Elmer, Varian, & Veeco. For Instruction Manual on the Agilent Varian 563 Ion Gauge, download the .pdf below at AVAILABLE DOWNLOADS. Typically Works With: Granville Phillips Models 260, 270, 280, 303, 306, 307 330, 340 ,350, and others. MKS Instruments 290, 919, 929 Perkin Elmer DGC3 Varian 831, 836, 842, 844, 845, 880, 971-0003, 971-0014, 971-1008, Multi-Gauge, Varian 572 Tube K7360301 Veeco RG2, RG3, RG21, RG31, RG81, RG83, RG84, RG830, RG840, RG1000, RG1002

OLD-STYLE Cable - Varian XGS-600 Controller to now Varian MBA-100 or MBA-200 Gauges, 10 ft Fits Legacy Metal Bayard-Alpert Gauges and also works with old Multi-Gauge and SenTorr Controllers. These cables are old-style that work with the legacy MBA-100 and MBA-200 metal hot cathode ion gauges. These cables are new and will be offered as long as they are available in our inventory. These Agilent Varian XGS-600 cables to old-style discontinued MBA 100 and MBA 200 hot cathode ion vacuum gauges are 10 foot long. They fit the HFIG card inside the XGS-600 controller for vacuum gauges having part number R32483010. They are new and come with full Agilent Varian warranty. These cables are for MBA 100 and MBA 200 old style all metal sensors to XGS 600 (HFIG card), only.These cables are compatible with the following Old Style Varian controllers as well: XGS-600 Controller Multi-Gauge Controller SenTorr Controller

Newest-Style Agilent Varian MBA2-200T Hot Cathode Filament Gauge, Dual Tungsten, Mini All Metal Case Baird Alpert Gauge, KF25, NW25 Flange Works With Newest-Style XGS-600 Hot Cathode Gauge CardsThese Agilent Varian MBA2-200T Hot Filament Gauges connect to the Newest-Style Agilent Varian XGS-600 hot cathode gauge controller cards. These Hot-cathode Bayard-Alpert Ion Gauges are the smallest Ion gauges. They are much more rugged than glass tubes and have an all metal case. They generate less heat and provide greater burnout resistance. They can measure pressure down to 3x10-10 Torr. They come in dual tungsten or burn out resistant dual yittria coated iridium filaments providing long gauge life. These have a KF25, NW25 vacuum flange fitting. Agilent XGS-600 vacuum gauge controller connection cable is required for use and sold on this website (see middle picture above, PN P106293, 10ft.) This is the gauge only. The controller connection cable is not included. PDF instruction manual for use can be downloaded below in the available downloads.

Newest-Style Agilent Varian MBA2-200T Hot Cathode Filament Gauge, Dual Tungsten, Mini All-Metal Case Baird Alpert Gauge, KF40, NW40 Flange Works With Newest-Style XGS-600 Hot Cathode Gauge CardsThese Agilent Varian MBA2-200T Hot Filament Gauges connect to the Agilent Varian XGS-600 hot cathode gauge controller cards. These Hot-cathode Bayard-Alpert Ion Gauges are the smallest Ion gauges. They are much more rugged than glass tubes and have an all metal case. They generate less heat and provide greater burnout resistance. They can measure pressure down to 3x10-10 Torr. They come in dual tungsten or burn out resistant dual yittria coated iridium filaments providing long gauge life. These have a KF40, NW40 vacuum flange fitting. Agilent XGS-600 vacuum gauge controller connection cable is required for use and sold on this website. This is the gauge only, controller connection cable not included. PDF instruction manual for use can be downloaded below in the available downloads.

Agilent Varian MBA2-200T Hot Cathode Filament Bayard-Alpert Gauge, Dual Yittria Iridium, KF25, NW25 Flange Mini All-Metal Case for Newest-Style XGS-600 Hot Cathode Gauge CardsThese Agilent Varian MBA2-200T Hot Filament Gauges connect to the Newest-Style Agilent Varian XGS-600 hot cathode gauge controller cards . These Hot-cathode Bayard-Alpert Ion Gauges are the smallest Ion gauges. They are much more rugged than glass tubes and have an all metal case. They generate less heat and provide greater burnout resistance. They can measure pressure down to 3x10-10 Torr. They come in dual tungsten or burn out resistant dual yittria coated iridium filaments providing long gauge life. These have a KF25, NW25 vacuum flange fitting. Agilent XGS-600 vacuum gauge controller connection cable is required for use and sold on this website (see middle picture above, PN P106293, 10ft.) This is the gauge only, controller connection cable not included. PDF instruction manual for use can be downloaded below in the available downloads.

Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 10 ft.Works With XGS-600 Hot Cathode Gauge Cards These Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest style MBA 2-200T to hot cathode gauge controller (HFIG) card for XGS-600 controller and have Agilent Varian part number X3203-60006. These come with full Agilent Varian warranty. These cables are for the newer versions of the MBA 2-200T dual filament full metal hot cathode ion gauge sensors to XGS 600 controller’s only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors. Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 50 ft. (New Style)Works With Newest-Style XGS-600 Hot Cathode Gauge CardsThese Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest-style MBA 2-200T to hot cathode gauge controller (HFIG) cards for XGS-600 controller. These come with full Agilent Varian warranty. These cables are for the newer versions of the MBA 2-200T dual filament full-metal hot cathode ion gauge sensors to XGS 600 controller’s only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors.Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Agilent Varian XGS-600 Vacuum Gauge Controller to MBA2-200T Hot Cathode Ion Vacuum Gauge Cable, 25 ft. Works With XGS-600 Hot Cathode Gauge Cards These Agilent Varian XGS-600 to MBA2-200T hot cathode ion vacuum gauge cables work with the newest-style MBA 2-200T to hot cathode gauge controller (HFIG) cards for XGS-600 controller. These come with full Agilent Varian warranty. These new cables are for the newer versions of the MBA 2-200T dual filament full metal hot cathode ion gauge sensors to XGS 600 controller’s only, not compatible with Old Style Varian MBA-100 and MBA-200 sensors. Can be used with the following Agilent Varian Controllers: XGS-600 Vacuum Gauge Combination Controller

Agient Varian 531 Thermocouple Vacuum Pressure Measurement Gauge Tube Sensor, 4 VCR® FEMALE SS, Laser Weld The Varian 531 thermocouple gauge tube sensor provides continuous accurate indication of total pressure from 1 x 10-3 Torr to 2.0 Torr (1X10-3 mbar to 2.7 mbar). Developed to combine rugged dependability and outstanding performance for roughing and foreline pressure measurement. The Varian 531 thermocouple vacuum gauges are a low cost pressure measurement sensor. The Varian 531 thermocouples tube sensors offers high resistance to vibration this model is Stainless Steel and Laser Welded. Thermocouple Vacuum Pressure GaugesThermal conductivity gauges rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. A common variant is the Pirani gauge which uses a single platinum filament as both the heated element and RTD. These gauges are accurate from 20 Torr to 10-3 Torr (depending on the model of sensor and controller purchased). However, they are sensitive to the chemical composition of the gases being measured and are termed a relative pressure measurement method, that is, they determine the pressure indirectly from the thermal conductivity property of the gas medium.

Agilent Varian 531 Thermocouple Vacuum Pressure Gauge Simulator and Reference Tube. This is an Agilent Varian 531 Thermocouple Gauge Simulator and Reference Tube. It simulates both 2.0 Torr pressure and 1 × 10-3 Torr. The Reference Tube is permanently sealed with a vacuum inside at a Pressure of <=5 × 10-6 Torr. Thermocouple Vacuum Pressure GaugesThermal conductivity gauges rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. A common variant is the Pirani gauge which uses a single platinum filament as both the heated element and RTD. These gauges are accurate from 20 Torr to 10-3 Torr (depending on the model of sensor and controller purchased). However, they are sensitive to the chemical composition of the gases being measured and are termed a relative pressure measurement method, that is, they determine the pressure indirectly from the thermal conductivity property of the gas medium.

This Serial Protocol Cable is used to transfer data from an Ideal Vacuum TIC Controller or any other vacuum gauge controller with an RS232 serial output to a computer equipped with a standard RS232 serial port. It is designed for use with older computers that have a built-in DB9 serial interface.The cable provides a reliable RS232 serial connection for communicating with compatible vacuum gauge controllers, allowing users to monitor vacuum pressure readings, configure controller settings, and transfer data using RS232 serial communication.Compatible controllers include:Ideal Vacuum XG-120 Thermocouple Gauge Controller (P108447) Edwards Active Digital Pressure Controller (P107267) Edwards TIC Instrument Controller (P107177) This cable is intended for computers with a built-in RS232 DB9 serial port. For computers equipped only with USB ports, use the Ideal Vacuum Serial-to-USB Cable Connectivity Kit (sold separately).

Varian Agilent XGS-600 Gauge Controller Tilt Stand Accessory, Optional Accessory, Agilent Varian Part Number R3124301. This is a Varian Agilent XGS-600 Gauge Controller Tilt Stand Accessory, Optional Accessory. This is the Tilt Stand Only all gauges, cables, and vacuum controllers sold separately on this website. Agilent Varian Part Number R3124301. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Rack-Mounting Kit, 19 Inch, ON Center, Optional AccessoryThis is a Varian Agilent 19 inch rack mounting, ON center kit for the XGS-600 Multi-gauge Controller. This is the rack kit only all gauges, cables, and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 Gauge Controller Rack-Mounting Kit, 19 Inch, OFF Center, Optional Accessory This is a Varian Agilent 19 inch rack mounting, OFF center kit for the XGS-600 Multi-gauge Controller. This is the rack kit only all gauges, cables, and vacuum controllers sold separately on this website.Can be used with the following Varian Agilent Controllers: XGS-600 Controller

Varian Agilent XGS-600 I/O Cable with Flying Leads, 50 foot Length. Varian Agilent Part Number R32493050. Varian Agilent XGS-600 I/O Cable with Flying Leads, 50 foot Length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following Varian Controllers: XGS-600 Controller

Varian Agilent XGS-600 I/O Cable with Flying Leads, 25 foot Length Varian Agilent XGS-600 I/O Cable with Flying Leads, 25 foot Length. This is the cable only. All gauges and controllers are sold separately on this website.Can be used with the following Varian Controllers: XGS-600 Controller

Varian Agilent XGS-600 I/O Cable with Flying Leads, 10 foot Length. Agilent Varian Part Number R32493010. Varian Agilent XGS-600 I/O Cable with Flying Leads, 10 foot Length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following Varian Controllers: XGS-600 Controller

Varian FRG-720 Bayard Alpert, Pirani to GXS-600 Vacuum Gauge Controller, Active Port CABLE, 10 Foot LengthThis is a Varian Agilent signal cable and hooks up to the XGS-600 controller to the Varian FRG-720 Active Gauge Sensor Tube. Cable standard 10 foot length. This is the cable only all gauges and controllers sold separately on this website. Can be used with the following controller: Varian XGS-600

Varian Agilent XGS-600, Multi-Gauge, and SenTorr Gauge Controller to Nude Ion Gauge (Varian, Inc. models UHV-24 or UHV-24p) Sensor Tube Cable, 10 foot length, non-bakeableThis is a Varian Agilent signal cable and hooks up to the XGS-600, Multi-Gauge, and SenTorr Gauge Controller to the Varian Glass Ion Sensor Tubes, UHV-24 or UHV-24p. Cable standard 10 foot length. This is the cable only all gauges and vacuum controllers sold separately on this website. Can be used with the following Varian Agilent Controllers: XGS-600 Controller Multi-Gauge Controller SenTorr Controller

Varian Agilent XGS-600 controller, Multi-Gauge controller, SenTorr Gauge Controller to Varian IMG100 or IMG300 Inverted Magnetron Gauge Sensor Tube CABLE. Signal cable, standard 10 foot length, Non-bakeable. This is a Varian Agilent signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller to the Varian IMG100 or IMG300 Inverted Magnetron Gauge Sensor CABLE. Cable standard 10 foot length. Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge ControllerThis is a the signal cable ONLY. Sensors and controllers are sold separately on this website.

Agilent Signal Cable for XGS-600, or SennTorr Gauge Controller to Thermocouple Sensor, 50 foot length. This is a Agilent Varian signal cable and hooks up to the XGS-600 controller, Multi-Gauge controller or SenTorr Gauge Controller and connects to Agilent Varian ConvecTorr Sensors. Cable 50 foot cable length.Can be used with the following controllers: Varian Multi-Gauge Controller Varian Senn Torr Gauge Controller Varian XGS 600 Gauge Controller This is a the signal cable ONLY. Sensors and controllers sold separately on this website.

Agilent Varian Inverted Magnetron Ion Gauge (IMG) for XGS-600 Multi-Gauge Vacuum Controller, Agilent Varian This is the Agilent Varian (IMG) Inverted Magnetron Board and operates the Ultra High Vacuum IMG-100 and IMG-300 gagues. It allows you to set the gauge sensitivity value, and gas correction factor. The (UHV) Ultra High Vacuum range is standard, as is remote I/O control of emmission and 0 to 10 V analog output.Compatible with the following gauges in the ultra high vacuum range from 10-9 to 10-10: IMG-100, IMG-300 (UHV) Also compatible with competitors gauges (see XGS-600 Instruction/Users Manual .pdf page 2-4 for Cross Reference below.) This is the Inverted Magnetron Ion Gauge (IMG) ONLY. For Complete Board Specifications/Descriptions see XGS-600 Instruction/Users Manual .pdf page A-3 below. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards: Slots are numbered left to right as viewed from the front of the XGS-600 controller.Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG boards are long high profile cards and can only be installed in slots 1-4 Option slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5. For a full explanation of field installation of add on cards - see the .pdf’s (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

Varian Agilent Dual Analog Input Card for the XGS-600 Multi-Gauge Controller.This is a Dual Analog Input Card for the XGS-600 Multi-Gauge Controller. Depending on the XGS-600 Controller configuration it may or may not have this Dual Analog Input Card. With 1 Analog Input Card the XGS-600 Controller can read 2 active gauges (2 active gauges per card). Up to 6 Dual Analog Input Cards can be installed in the XGS-600 Controller, for a total of 12 active gauge inputs. Other cards can also be used along side this Dual Analog Input Card.Compatible with the following Varian Agilent active gauges: CT-100, PVG-500, Rough Vacuum Atm to 10-3 CDG-500, PCG-750, High Vacuum 10-3 to 10-9 FRG-700, FRG-720/730, High Vacuum 10-3 to 10-9 This is the Dual Analog Input Card ONLY. The XGS-600 Controller, other cards, gauges and cables sold separately on this website. PCB Board/Card Installation: Procedures for installing add on cards :Slots are numbered left to right as viewed from the front of the XGS-600. Option slots 1-4 are long high profile slots and can accomodate any card/board. HFIG Boards are long high profile cards and can only be installed in slots 1-4. Option Slots 5-6 are short, low profile slots and can accomodate only convection or IMG Boards with the following restrictions. An IMG Board may not be installed in slot 5 if any other board is installed in slot 4. An IMG Board may not be installed in slot 6 if any other board is installed in slot 5.For a full explanation of field installation of add on cards - see the pdf’s (Replacement Card Instruction Sheet .pdf and the Vacuum Measurement Brochure .pdf page 11) by scrolling down to AVAILABLE DOWNLOADS)

Agilent Varian CDG-500 Capacitance Diaphragm Manometer Gauge, No set points. Pressure Range: 1 Torr, KF16 Flange.Works with Agilent XGS-600 Vacuum Gauge Controller and the Active Gauge Controllers AGC-100, AGD-100. The Capacitance Diaphragm Gauge CDG-500 is intended for absolute pressure measurement of gases in its respective pressure range. This unit measures 1 Torr. The gauge can be operated in connection with an AGC-100, AGD-100 or XGS 600 Vacuum Gauge Controller, an Agilent Turbo AG Rack Controller, or with another appropriate measuring unit. The Capacitance Diaphragm Gauge consists of a capacitive sensor element made of a corrosion resistant ultra pure alumina ceramic diaphragm providing exceptional signal stability, fast recovery from atmosphere, short warm-up times and unparalleled robustness. The electronics converts the capacitance into a DC voltage output signal. The output signal is linear to the measured pressure and independent of the gas type. This unit provides a high level of accuracy in the high pressure range of 1 Torr. This is the Agilent Varian CDG-500 Capacitance Diaphragm Gauge Only, (no set points), signal cable and controller sold separately on this website. For more data scroll down to (AVAILABLE DOWNLOADS:) and download the Spec Sheet and other pertinent pdfs. Can be used with the following Agilent Varian Controllers: Agilent Varian XGS 600 Gauge Controller Agilent Varian Active Gauge Controllers AGC-100, AGD-100

Agilent Varian CDG-500 Capacitance Diaphragm Manometer Gauge, No set points. Pressure Range: 1000 Torr, KF16 Flange.Works with Agilent XGS-600 Vacuum Gauge Controller and the Active Gauge Controllers AGC-100, AGD-100The Capacitance Diaphragm Gauge CDG-500 is intended for absolute pressure measurement of gases in its respective pressure range. This unit measures 1000 Torr. The gauge can be operated in connection with an Agilent AGC-100, AGD-100 or XGS 600 Vacuum Gauge Controller, an Agilent Turbo AG Rack Controller, or with another appropriate measuring unit.The Capacitance Diaphragm Gauge consists of a capacitive sensor element made of a corrosion resistant ultra pure alumina ceramic diaphragm providing exceptional signal stability, fast recovery from atmosphere, short warm-up times and unparalleled robustness. The electronics converts the capacitance into a DC voltage output signal. The output signal is linear to the measured pressure and independent of the gas type. This unit provides a high level of accuracy in the high pressure range of 1000 Torr. This is the Agilent Varian CDG-500 Capacitance Diaphragm Gauge Only, (no set points), signal cable and controller sold separately on this website. For more data scroll down to (AVAILABLE DOWNLOADS:) and download the Spec Sheet and other pertinent pdfs. Can be used with the following Agilent Varian Controllers: Agilent Varian XGS 600 Gauge Controller Agilent Varian Active Gauge Controllers AGC-100, AGD-100

Agilent Varian CDG-500 Capacitance Diaphragm Manometer Gauge, No set points. Pressure Range: 10 Torr, KF16 Flange.Works with Agilent XGS-600 Vacuum Gauge Controller and the Active Gauge Controllers AGC-100, AGD-100. center> The Capacitance Diaphragm Gauge CDG-500 is intended for absolute pressure measurement of gases in its respective pressure range. This unit measures 10 Torr. The gauge can be operated in connection with an AGC-100, AGD-100 or XGS 600 Vacuum Gauge Controller, an Agilent Turbo AG Rack Controller, or with another appropriate measuring unit. The Capacitance Diaphragm Gauge consists of a capacitive sensor element made of a corrosion resistant ultra pure alumina ceramic diaphragm providing exceptional signal stability, fast recovery from atmosphere, short warm-up times and unparalleled robustness. The electronics converts the capacitance into a DC voltage output signal. The output signal is linear to the measured pressure and independent of the gas type. This unit provides a high level of accuracy in the high pressure range of 10 Torr. This is the Agilent Varian CDG-500 Capacitance Diaphragm Gauge Only, (no set points), signal cable and controller sold separately on this website. For more data scroll down to (AVAILABLE DOWNLOADS:) and download the Spec Sheet and other pertinent pdfs. Can be used with the following Agilent Varian Controllers: Agilent Varian XGS 600 Gauge Controller Agilent Varian Active Gauge Controllers AGC-100, AGD-100

Agilent Varian Replacement Nickel Sensor for the Active Pirani Gauge PVG-502, KF16 Flange.This is an Agilent Varian Replacement Nickel Sensor for the Active Pirani Gauge PVG-502 with a KF 16 Flange. The Pirani Standard Gauges PVG-500 and PVG-502 have been designed for vacuum measurement of gases in the pressure range of 5×10-4 … 1000 mbar. They must not be used for measuring flammable or combustible gases in mixtures containing oxidants (e.g. atmospheric oxygen) within the explosion range. They can be operated in connection with any VARIAN controller or with another controller.