Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller without Sensor This listing is for an XG-120 thermocouple gauge controller only (no sensor) and includes: XG-120 gauge controller 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 1 x 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller System with 1/8 NPT TC Gauge Tube This listing is for an XG-120 thermocouple gauge controller system and includes: XG-120 gauge controller Teledyne-Hastings DV-6M, 1/8" NPT gauge tube, (1 to 1000 mTorr reading) 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 1 x 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller System with 1/8 NPT TC Ruggedized Gauge Tube This listing is for an XG-120 thermocouple gauge controller system (with sensor) and includes: XG-120 gauge controller Teledyne-Hastings DV-6R, 1/8" NPT ruggedized gauge tube, (1 to 1000 mTorr reading) 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 1 x 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller System with KF-16 TC Gauge Tube This listing is for an XG-120 thermocouple gauge controller system (with sensor) and includes: XG-120 gauge controller Teledyne-Hastings DV-6M, KF-16 gauge tube, (1 to 1000 mTorr reading) 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller System with KF-25 TC Gauge Tube This listing is for an XG-120 thermocouple gauge controller system (with sensor) and includes: XG-120 gauge controller Teledyne-Hastings DV-6M, KF-25 gauge tube, (1 to 1000 mTorr reading) 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 1 x 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Ideal Vacuum XactGauge XG-120 Digital Thermocouple Vacuum Gauge Controller System with 4-VCR TC Gauge Tube This listing is for an XG-120 thermocouple gauge controller system (with sensor) and includes: XG-120 gauge controller Teledyne-Hastings DV-6M, 4-VCR gauge tube, (1 to 1000 mTorr reading) 10 ft. Gauge tube sensor cable (RJ12 to female octal connector) 1.5 A, 5VDC universal power adapter with 6 ft. cord (110-240VAC, 50/60Hz) Hardware kit for rack panel mounting The Ideal Vacuum XactGauge XG-120 Thermocouple (TC) Gauge Controller is a compact, all-in-one solution that provides low-noise, stable and repeatable roughing and foreline vacuum pressure measurements from 1 x 10-3 Torr to 1.999 Torr (1 to 1,999 mTorr). The XG-120 controller is housed in a 1/8 DIN enclosure, which can be either panel mounted or located on a bench top. It has tactile front control buttons and a large 6 digit red LED display for easy reading from across a room or in dimly lit locations. The gauge displays in mTorr, µbar and Pa and includes LED indicators for the two set points. The gauge is equipped with two (Type C) set point relays that can be used to activate valves or to control other external devices. The gauge also has RS232 serial and 5V analog linear outputs for quick integration into a wide variety of systems. The XG-120 uses inexpensive TC sensors which are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. The controller does not require recalibration when thermocouple gauge tubes are replaced. The XG-120 controller is available separately for use with your existing thermocouple gauge tubes and includes a power supply, a 10 ft. gauge tube sensor cable (RJ12 to female octal connector) and panel mounting hardware. Complete systems also include a Teledyne-Hastings DV-6 thermocouple gauge tube with choice of vacuum port (KF-16, KF-25, 1/8” NPT, or 4 VCR®). The manual is available here for download.

Teledyne-Hastings DV-6M 1/8" Male NPT, Thermocouple Vacuum Gauge Tube, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat

Teledyne-Hastings DV-6R 1/8" NPT Ruggedized Thermocouple Vacuum Gauge Tube, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat

Teledyne-Hastings DV-6M-KF-16 Thermocouple Vacuum Gauge Tube, KF16 (NW16) Fitting, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M-KF-16 thermocouple (TC) vacuum gauge tube with KF16 fitting, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat

Teledyne-Hastings DV-6M-KF-25 Thermocouple Vacuum Gauge Tube, KF25 (NW25) Fitting, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M-KF-25 thermocouple (TC) vacuum gauge tube with KF25 fittin, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat

Teledyne-Hastings DV-6M-4-VCR Thermocouple Vacuum Gauge Tube, 4-VCR Fitting, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M thermocouple (TC) vacuum gauge tube with 4-VCR fitting, measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company.

Teledyne-Hastings DV-36 Thermocouple Vacuum Gauge Tube, 0 to 1000 mTorr Range, High Temperatures and High Pressures, DV 6 series, 1/8 in. (0.125") NPT, Stainless Steel. PN: DV-36 This Teledyne-Hastings DV-36 DV 6 series Thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as "rough" indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat

Teledyne-Hastings DV-6R-CF Ruggedized Thermocouple Vacuum Gauge Tube, Conflat 1.33 Inch Fitting, 0.001 to 1 Torr Range This Teledyne-Hastings DV-6M 1/8" NPT thermocouple (TC) vacuum gauge tube measures pressure between 0.001 and 1 Torr (1 to 1000 mTorr) and calibrated for clean, dry air or nitrogen. DV-6 series gauge tubes are used with TC gauge controllers such as the Ideal Vacuum digital XG-120 and Teledyne-Hastings VT and DCVT units (not included). These inexpensive sensors are used as ‘rough’ indicators to monitor mechanical pump vacuum levels and to signal when crossover (to high-vacuum) pressure has been reached. Teledyne-Hasting DV-6 tubes are matched and gauge controller recalibration is not required when gauge tubes are replaced. Teledyne-Hastings DV-6 gauge tubes use a rugged, but sensitive noble metal thermocouple and corrosion resistant stainless steel and nickel plated components. They are temperature and temperature change-rate compensated, making them well suited for ambient installations. Standard DV-6 gauge tubes are rated for a maximum temperature of 100° C. Ruggedized gauge tubes are rated for 150° C. Thermocouple sensors (thermal conductivity gauges) rely on the fact that the ability of a gas to conduct heat decreases with pressure. In this type of gauge, a wire filament is heated by running current through it. A thermocouple or Resistance Temperature Detector (RTD) can then be used to measure the temperature of the filament. This temperature is dependent on the rate at which the filament loses heat to the surrounding gas, and therefore on the thermal conductivity. The Teledyne Hastings Instruments DV-6 thermocouple gauges have a reputation built upon exceptional stability, accuracy, and reliability under the most demanding conditions. DV-6 thermocouple gauge tube sensors are used in a wide variety of applications such as glove boxes, cryogenics, vacuum furnaces, pharmaceutical production, freeze drying, agricultural processes, air conditioning, thermal food containers, plasma coating, refrigeration (HVAC), accelerators, appliance manufacturing and many others. DV-6 series gauge tubes are available with several vacuum port configurations: DV-6M, Standard Tube with 1/8 inch Male NPT DV-6R, Ruggedized Tube with 1/8 inch NPT DV-6M-KF-16, Standard Tube with ISO KF-16 DV-6M-KF-25, Standard Tube with ISO KF-25 DV-6M-4-VCR, Standard Tube with Female ¼ inch VCR® DV-6R-CF, Ruggedized Tube with 1-1/3 inch Mini Conflat