Kinematic Optic Mount for 1" Diameter Optics, Standard, 2 Adjusters. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These anodized aluminum optic mounts fit round optics with 1" (25.4 mm) outer diameter. The mount has full exposure on the front face and a clear aperture of 0.95" (24.1 mm) for transparent optics. The inset is 0.25" (6.4 mm) from the front face but thicker optics may be mounted if they are allowed to protrude. The optic is held in place with a soft nylon tipped set screw which can be adjusted with a 5/64" standard hex key (Allen wrench). The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount, but is not centered on the optic face.

Kinematic Optic Mount for 1" Diameter Optics, Standard, 2 Adjusters, Vacuum Compatible. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These vacuum compatible aluminum optic mounts fit round optics with 1" (25.4 mm) outer diameter. The mount has full exposure on the front face and a clear aperture of 0.95" (24.1 mm) for transparent optics. The inset is 0.25" (6.4 mm) from the front face but thicker optics may be mounted if they are allowed to protrude. The optic is held in place with a soft nylon tipped set screw which can be adjusted with a 5/64" standard hex key (Allen wrench). The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount, but is not centered on the optic face.

Kinematic Optic Mount for 1" Diameter Optics, Clear Edge, 2 Adjusters, Vacuum Compatible. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These vacuum compatible aluminum optic mounts fit round optics with 1" (25.4 mm) outer diameter. The mounts leave two edges of the optic clear of support for applications where space is tight or a beam must transmit through the optic at an oblique angle. The maximum accepted optic thickness is 0.26" (6.6 mm). The optic is held in place with two 8-32 soft nylon tipped set screws which can be adjusted with a 5/64" standard hex key (Allen wrench). Very thin optics may require using longer set screws than those originally provided (0.375" length set screws are recommended to grip the thinnest of optics). The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount, but is not centered on the optic face.

Kinematic Optic Mount for 1" Diameter Optics, Clear Edge, 2 Adjusters. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These anodized aluminum optic mounts fit round optics with 1" (25.4 mm) outer diameter. The mounts leave two edges of the optic clear of support for applications where space is tight or a beam must transmit through the optic at an oblique angle. The maximum accepted optic thickness is 0.26" (6.6 mm). The optic is held in place with two 8-32 soft nylon tipped set screws which can be adjusted with a 5/64" standard hex key (Allen wrench). Very thin optics may require using longer set screws than those originally provided (0.375" length set screws are recommended to grip the thinnest of optics). The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount, but is not centered on the optic face.

Kinematic Platform Mount for Optics with Flat Mounting Surface, 1.0" x 1.9" Platform, 2 Adjusters. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These anodized aluminum optic mounts are equipped with a flat platform for mounting prisms, beamsplitter cubes, polarizers, diffraction gratings, or any other optic or object with a flat mounting surface. The platform has a depth of 1.0" and a width of 1.925" but can hold thicker optics if they are allowed to protrude. The platform can be removed and reattached to either leg of the optic mount using a 1/16" standard hex key (Allen wrench). The platform has ten 6-32 mounting holes along the perimeter which may be used to mount the optic directly or with Ideal Vacuum’s optional adjustable optic mounting arm S101085. The adjustable optic mounting arm holds the optic in place with a soft nylon tipped set screw which can be tightened with a 5/64" standard hex key. For permanent mounting, glue may be used instead. The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount.

Kinematic Platform Mount for Optics with Flat Mounting Surface, 1.0" x 1.9" Platform, 2 Adjusters, Vacuum Compatible. 8-32/M4 Socket Head Cap Screw Mounting. Sold 1 Each. These vacuum compatible aluminum optic mounts are equipped with a flat platform for mounting prisms, beamsplitter cubes, polarizers, diffraction gratings, or any other optic or object with a flat mounting surface. The platform has a depth of 1.0" and a width of 1.925" but can hold thicker optics if they are allowed to protrude. The platform can be removed and reattached to either leg of the optic mount using a 1/16" standard hex key (Allen wrench). The platform has ten 6-32 mounting holes along the perimeter which may be used to mount the optic directly or with Ideal Vacuum’s optional adjustable optic mounting arm S101085. The adjustable optic mounting arm holds the optic in place with a soft nylon tipped set screw which can be tightened with a 5/64" standard hex key. For permanent mounting, glue may be used instead. The mount is equipped with two 1/4"-80 fine adjustment screws which tip the optic in the x and y directions for easy alignment and beam steering. The mount has two mounting holes that fit 8-32 or M4 socket head cap screws. Each mounting hole is laterally centered on the optic mount.

Adjustable Optic Clamping Arm Accessory for Kinematic Platform Mount, 2" Threaded Post, 6-32 Thread. This anodized aluminum adjustable optic clamping arm on a 303 non-magnetic stainless steel post is used to hold optics up to 1-1/2" tall in place. Use it with ideal vacuums kinematic platform mount. S101084 The arm height and rotation may be adjusted by loosening the socket head cap screw clamping the arm to the post using a 3/32" standard hex key (Allen wrench). The adjustable optic mounting arm holds the optic in place with a soft nylon tipped set screw which can be tightened with a 5/64" standard hex key. Longer or shorter optical posts can be used to further customize. The 2" threaded post has a 6-32 thread that matches Ideal Vacuum’s kinemetic platform mounts. The post can be further tightened by inserting a 1/16" hex key or other suitably sized lever through the cross-drilled 0.1" diameter hole in the post.

Adjustable Optic Clamping Arm Accessory for Kinematic Platform Mount, 2" Threaded Post, 6-32 Thread, Vacuum Compatible This uncoated aluminum adjustable optic clamping arm with a 303 non-magnetic stainless steel post is designed to securely hold optics up to 1-1/2" tall in place. It is designed for use with the Ideal Vacuum Kinematic Platform Mount, S101206. The arm height and rotation can be adjusted by loosening the socket head cap screw that clamps the arm to the post using a 3/32" standard hex key (Allen wrench). The adjustable optic clamping arm holds the optic securely in place with a soft nylon-tipped set screw, which can be tightened using a 5/64" standard hex key. Longer or shorter optical posts can also be used to further customize the mounting configuration. The 2" threaded post has a 6-32 thread that matches Ideal Vacuum’s kinematic platform mounts. The post can be further tightened by inserting a 1/16" hex key or other suitably sized lever through the cross-drilled 0.1" diameter hole in the post.