MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 0.4 to 20 sccm, 15-pin D-subminiature, 4 VCR® Male. MKS Part Number: GM50A013201RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 0.4 to 20 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 1 to 50 sccm, 15-pin D-subminiature Connector, 4 VCR® Male. MKS Part Number: GM50A013501RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 1 to 50 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 2 to 100 sccm, 15-pin D-subminiature Connector, 4 VCR® Male. PN: GM50A013102RMM020. MKS Part Number: GM50A013102RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 2 to 100 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 4 to 200 sccm, 15-pin D-subminiature Connector, 4 VCR® Male. MKS Part Number: GM50A013202RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 4 to 200 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 10 to 500 sccm, 15-pin D-subminiature Connector, 4 VCR® male. MKS Part Number: GM50A013502RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 10 to 500 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS GM50A Mass Flow Controller (MFC) Analog-Controlled, Range of 20 to 1000 sccm, 15-pin D-subminiature Connector, 4 VCR® Male. MKS Part Number: GM50A013103RMM020. This MKS GM50A Mass Flow Controller is calibrated for N2 or equivalent, with a control range of 20 to 1000 sccm. It has a 15-pin D-subminiature analog connector with tied grounds and 0-5 VDC flow input and output signals. The gas inlet and outlet fittings are Swagelok® 4 VCR® male. The valve seal is normally closed and made of Teflon™. Typical response times are on the order of 500 milliseconds. Swagelok® and VCR® are registered trademarks of Swagelok Company. Vac Goop™ is a trademark of Swagelok Company. Ideal Vacuum Products is not an authorized distributor of Swagelok Company. Teflon-TM The Chemours Company FC, LLC.

MKS 946 Half-Rack Vacuum Gauge Controller Power Supply and Readout, NO Cards, RS232 and RS485, 6 Channels. MKS Part Number: 946-US-NANANA-NA. The MKS 946 is a versatile half-rack vacuum gauge measurement and control system, it provides power and simultaneous readout for up to six different vacuum gauges and/or mass flow controllers, with options for controlling pressure. This is a raw unit without cards. Power Supplies/Readouts are designed to control and display any flow transducer. The flow rate set point can be adjusted either through front panel controls or remotely through the rear panel analog interface. The 946 Vacuum System Controller is a six channel/sequentially selectable single readout. Compatible with mass flow controllers and mass flow readouts. Signal cables and optional cards for the MKS 946 are available on this website.

MKS 937B Mass Flow Control Card For Series 946 Controllers and Dual Mass Flow Controllers. MKS Part Number: 20000712. The MKS 937B Mass Flow Control Card is compatible with the 946 and dual Mass Flow controllers. These cards are used on controllers designed to control and display any flow transducer. The flow rate set point can be adjusted either through front panel controls or remotely through the rear panel analog interface. The 946 Vacuum System Controllers simultaneous readout & control of up to 6 sensors and gauges.

MKS Vacuum Gauge Cable Connects 946 Controller to 179, 1179, 1462, 1479, 1559, 2179, GE50A, GM50A, IE50A, IM50A, IM250A, P250A, 10 ft. (3m) Long. MKS Part Number: 100016744. The MKS Mass Flow Controller Cable connects 179, 1179, 1462, 1479, 1559, 2179, GE50A, GM50A, IE50A, IM50A, IM250A, P250A mass flow controllers to 946 controllers with 15-pin type D High-density subminiature to 15-pin standard subminiature connectors. This is the Cable ONLY. The MKS 946 is a versatile half-rack vacuum gauge measurement and control system, it provides power and simultaneous readout for up to six different vacuum gauges and/or mass flow controllers, with options for controlling pressure. Power Supplies/Readouts are designed to control and display any flow transducer. The flow rate set point can be adjusted either through front panel controls or remotely through the rear panel analog interface. The 946 Vacuum System Controller is a six channel/sequentially selectable single readout. Compatible with mass flow controllers and mass flow readouts. Signal cables for the MKS 946 are available on this website.

MKS Vacuum Gauge Cable Connects 946 Controller to 179, 1179, 1462, 1479, 1559, 2179, GE50A, GM50A, IE50A, IM50A, IM250A, P250A, 25 ft. (7.5m) Long. MKS Part Number: 100016745. The MKS Mass Flow Controller Cable connects 179, 1179, 1462, 1479, 1559, 2179, GE50A, GM50A, IE50A, IM50A, IM250A, P250A mass flow controllers to 946 controllers with 15-pin type D High-density subminiature to 15-pin standard subminiature connectors. This is the Cable ONLY. The MKS 946 is a versatile half-rack vacuum gauge measurement and control system, it provides power and simultaneous readout for up to six different vacuum gauges and/or mass flow controllers, with options for controlling pressure. Power Supplies/Readouts are designed to control and display any flow transducer. The flow rate set point can be adjusted either through front panel controls or remotely through the rear panel analog interface. The 946 Vacuum System Controller is a six channel/sequentially selectable single readout. Compatible with mass flow controllers and mass flow readouts. Signal cables for the MKS 946 are available on this website.